Search:

Type: Posts; User: Frizie

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    7

    Re: Password website

    I don't want to start a new topic but I want to report (apart from this topic) that I also find it strange that one time the newest item is on top and another time below.
    Then all messages are...
  2. Replies
    10
    Views
    11

    Re: HBUSIN stops program?

    A benefit of the (software) commands I2CIN and I2COUT is that you can apply these to almost all port-pins.
    Incidentally, remember that there should be a short delay after I2COUT (= writing to) when...
  3. Replies
    10
    Views
    11

    Re: HBUSIN stops program?

    Succes! :triumphant:
    Bút with I2IN / I2COUT on the standard ports (PORTC.3 SCL / PORTC.4 SDA)
    And I shouldn't declare the PPS even if it's the standard PORTs (as I did in the examples in this...
  4. Replies
    10
    Views
    11

    Re: HBUSIN stops program?

    Hi Les.

    Today I'm working further on my PIC program to get the I2C EEPROM working together with the PPS, but I found another anomaly.
    I get an assembler error when I activate DECLARE HSERIN2_PIN...
  5. Replies
    10
    Views
    11

    Re: HBUSIN stops program?

    Thanx Tim.

    I didn't knew that, so now I can look further.
    Then I guess there is still something wrong with the PPS settings, because on an old 18F452 the same routine with the same external...
  6. Replies
    32
    Views
    33

    Re: New PICkit 4 available

    Thanks John and Lester, for placing the article! :rapture:

    Best regards,
    Frizie.
  7. Replies
    10
    Views
    11

    HBUSIN stops program?

    Hi people.

    I've a problem with HBUSIN (HBUSOUT not tried yet)
    If I activate this command, then the program stops by this command.



    DEVICE = 18F45K40
  8. Replies
    2
    Views
    3

    Re: Assembler errors on V3.6.1.7

    Thanks for the quick response Les!
    You doing a very great job, but I guess you know :smug:

    Unfortunately I don't have the time to work on my own website (so much other work in electronics, pfff),...
  9. Replies
    32
    Views
    33

    Re: New PICkit 4 available

    Hi guys!

    Today I received my PICkit4. :biggrin:
    Fingers crossed, but until now it works as it should and nice and fast.

    For those who also have PICkit4, here is how to work together with...
  10. Replies
    2
    Views
    3

    Assembler errors on V3.6.1.7

    Hi guys.

    Today I received my PICkit4! LOL
    But before I go try this programmer/debugger, I have noticed assembler errors on compiler V3.6.1.7

    Device: 18F45K40
    I can't give the next:
  11. Re: Why stays a part of RAM empty when I turn on RC1IE (18F45K40)?

    Whooo, after updating to V3.6.1.7, it looks like the problem is solved!
    But I think I read somewhere on the forum that V3.6.1.7 was not correct.
    I did not see it in folder 'DOWNLOAD' either, so I...
  12. Re: Why stays a part of RAM empty when I turn on RC1IE (18F45K40)?

    Really no one a single idea what the problem is? :numbness:

    Les, do you have any idea or are you already working on it?
    Cause I suspect that the compiler V3.6.1.6 did not convert the program...
  13. Re: Why stays a part of RAM empty when I turn on RC1IE (18F45K40)?

    Thanks for respons gentlemen.
    I was not sure yet and was already hoping for a response to this, outside the RAM problem itself.

    The RAM problem also occurs even if I remove the whole interrupt...
  14. Why stays a part of RAM empty when I turn on RC1IE (18F45K40)?

    I have something strange, I'm loosing RAM values in the Basic program and a PIC18F45K40 underneath.
    (It's part of a bigger program, but the issue is still in the example here)

    If I run the next...
  15. Replies
    103
    Views
    104

    Re: Got a stopbadware.org warning this morning.

    Lester, I go for option (4) (from your option-list in #86).

    But isn't it easier to turn all weblinks into normal text (maybe with another -blue- color)?
    Then Google have no problem anymore with...
  16. Thread: Proton Studio

    by Frizie
    Replies
    38
    Views
    39

    Re: Proton Studio

    I closely follow this topic.
    Thumbs up for John and Proton Studio!
  17. Replies
    6
    Views
    7

    Password website

    Pfff, annoying, every six months first come up with asking for a new password and that only for a forum...
    No other forum does that. :orange:
    I have been annoyed by this for years!
    You chase away...
  18. Replies
    3
    Views
    4

    Re: 12F617 will not compile

    Excuse for my late response, but thanks for the quick solution Les.
    The latest version compiles the 12F617 as in the old days :fat:
  19. Replies
    3
    Views
    4

    12F617 will not compile

    Hi Les.

    Thank you for updating to V3.6.1.4.
    You're doing a great job, fantastic compiler for so many years!

    I've found an old issue for the 12F617.
    It gives assembler errors in compiler...
  20. Replies
    16
    Views
    17

    Re: Support for Les... a change of heart?

    I want to sponsor Les with a donation but I don't have PayPal.
    Isn't there a bank account?

    Frizie
    picbasic.nl
  21. Replies
    18
    Views
    19

    Re: PicKit3 Programmer

    John, how do you start programming your PICkit3 programmer?
    From out of Proton IDE with a touch on F10 / F11? (what I prefer)
    Or do you have to swap to MPLAB after you've compile a Proton program?...
  22. Thread: Issue with MID$

    by Frizie
    Replies
    5
    Views
    6

    Re: Issue with MID$

    George, the only reason I opened this thread is to report the compiler issue with "Unbalanced parenthasis!", not for solving a program problem I should have (I have solve it directly by swapping 2...
  23. Thread: Issue with MID$

    by Frizie
    Replies
    5
    Views
    6

    Re: Issue with MID$

    Thanks for reply George.

    But 'OffsetNeg' is a bit, not a byte.

    The bit will be TRUE when a offset temperature comes under 0 degrees Celsius, then it haves to place a minus character before the...
  24. Thread: Issue with MID$

    by Frizie
    Replies
    5
    Views
    6

    Issue with MID$

    Hi people!

    I have a small issue with the MID$ command.
    If I put a semi-colon in the source-string then I get the compiler error: Unbalanced Parenthasis!


    DIM DisplayTekst AS STRING * 20...
  25. Replies
    6
    Views
    7

    Re: How convert ASCII to char?

    My apologies John.

    Even your solution I've completely overlooked.
    I don't know what I had yesterday.
    Was I blind? :hopelessness: Drunk without a drop alcohol? :very_drunk: I don't know.

    But...
  26. Replies
    6
    Views
    7

    Re: How convert ASCII to char?

    Thanks Les,

    Your answer is the solution, indeed no ASC instruction necessary.
    I'm sleepy ánd stupid today, because I could think of that solution too.
    But in all my craziness, I was completely...
  27. Replies
    6
    Views
    7

    How convert ASCII to char?

    Les, it would be nice if Proton PIC Basic will get the instruction 'ASC' (like other Basic compilers) to convert the ASCII value from a character into a BYTE value.
    All other threads I've read here,...
  28. Sticky: Re: Proton 3.5.8.6 and Proton24 1.0.3.5 available for download

    Les, I'm getting an assembler error on a PIC Basic program with version V3.5.8.6 (Error[126] Argument out of range (263 not between -256 and 255))
    The error appears on a 16F1938 and 16F1939.
    I'm...
  29. Replies
    38
    Views
    14,233

    Re: PDS File Clean up PlugIn

    Hi folks.

    I want to download PDS Clean Up plug-in, from Wiki.
    But if I click on it, I get the report "404 Not Found"

    Does someone have this file for me or is there a reason for it?

    Regards,...
  30. Replies
    2
    Views
    2,048

    Re: No error message in SEROUT

    I've checked the assemblercode in 3.5.5.5 and still the same.
    Problem is the compiler turns the "variablename" itself as text as output, instead as give an error message, if the variable isn't...
  31. Replies
    2
    Views
    2,048

    No error message in SEROUT

    Hi.

    Found a small issue (I still use 3.5.5.5, but I think the newer versions still have it because none has notice).

    When I write SEROUT PORTB.2, 84, [Frizie] then I get an error message,...
  32. Re: Small editor issue 2.0.1.2 (3.5.5.4, maybe also 3.5.5.5?)

    Thanks for reply Joseph.

    Unfortunately a lot of times I'm really working in both (or 3) PIC Basic programs at the same time, because the 2 (or 3) PIC's are master and slaves on the same board....
  33. Small editor issue 2.0.1.2 (3.5.5.4, maybe also 3.5.5.5?)

    I work the last few months about 10 hours a day with Proton and PIC controllers.
    The longer I work with it, I see, this-is-just-a-super-compiler :D
    I'm very pleased about it.

    The projects I work...
  34. Replies
    13
    Views
    2,939

    Re: Is there any interest in some Modbus code

    Hi Tim.

    On this moment I'm very busy with writing a big program with modbus communication, but I've build my own modbus routine and it works without problems.
    Ofcourse I'm very curious about your...
  35. Thread: CAN - CanOpen

    by Frizie
    Replies
    7
    Views
    2,508

    Re: CAN - CanOpen

    Hi John.

    Remember, it's just a wish.

    I'm only familiar with programming in Basic.
    I don't know how I should write new commands for the Proton compiler, thats why I put my wish in the Wish List...
Results 1 to 35 of 100
Page 1 of 3 1 2 3